Overspanningsbeveiliging voor verschillende voltages

Deelbare, meerpolige universele bliksemstroom- en overspanningafleider voor toepassing in ICT systemen. De XTU kan worden toegepast binnen het voltagebereik van 0-180V d.c. De insteekmodule, voorzien van Lifecheck voorziet in contactloos testen waarbij de rapportage kan worden verzorgd via USB. Door toepassing van het MCM monitoringsysteem kan de afleider op basis van potentiaalvrij wisselcontact op afstrand gemeld worden.

• Universele voltage door actiVsense technologie wordt de uitgangspanning op de inputspanning aangepast
  
• Voorzien van Lifecheck^® monitoringsysteem
  
• Maak vóór verbreek contact voor inbedrijfstelling (en oplevering) van installatie vóór plaatsen insteekmodule. Plaatsen/ uitnemen insteekmodule zonder signaalonderbreking

Technische informatie BLITZDUCTOR^® XTU - in engels

Conditie Monitoring Systeem

• Updated gebruiker software
  
• Eenvoudige gebruikersvriendelijke applicatie
  
• Statusindicatie van beveiligingsmodules
  
• Uitbreidingmogelijkheden

Gebruikers software voor statusweergave van DRC MCM XT module en aangesloten BLITZDUCTOR^® modules voorzien van Lifecheck^®. BLITZDUCTOR^® modules kunnen door toepassing van de software op afstand uitgelezen en gereset worden door de geïntegreerde “Service Console” module. De software kan via deze link kosteloos worden gedownload.

Technische informatie DRC MCM XT - in engels
Software

Bliksemstroom- en overspanningsafleider

Bliksemstroom- en overspanningsafleider voor het beveiligen van analoge video signalen zoals CCTV etc

Ruimtebesparende overspanningsbeveiliging voorzien van BNC connector en montage op 35mmDIN rail. Beschikbaar in uitvoering met directe (VCD) en indirecte (VCID) aardemantelverbinding ter voorkoming van aardloops

Space-saving surge arrester with BNC socket connector for mounting on supporting rails for protecting video and camera systems. Available with direct (VCD) or indirect shield connection (VCID), according to type, to avoid leakage pickups

Technische informatie DGA BNC VCD/VCID

Lightning current / Surge arrester Type 1

• For d.c. supplies up to a nominal current of 4 A
  
• Low voltage protection level suitable for protection of terminal equipment
  
• Can be used according to the lightning protection zones concept at boundaries 0_A-2 and higher

BLITZDUCTOR VT ALD 36 is a Type 1 combined lightning current and surge arrester. It is ideally suited for protecting terminal equipment with an immunity according to test level 1 in compliance with EN 61000-4-5. The arrester was tested in accordance with EN 61643-21 and energy-coordinated in accordance with IEC 61643-22 for protecting unearthed d.c. power supplies with nominal currents up to 4 A. The BVT arrester is designed for mounting on a 35 mm DIN rail in accordance with EN 60715. High-grade connections via screw clamps for a conductor cross-section of 0.5 to 4.0 mm² are used. The two-pole arrester features two earth terminals and has a width of 1.5 modules.

Portable test device DRC LC M3

Portable device with LifeCheck sensor for flexible use. Provides visual and acoustic ''OK'' indication for identified LifeCheck circuits in SPDs. With additional USB connection for PC-aided administration of test samples and documentation of the test results. DRC LC M3 can save the date of the last test on BXT and helps to program the same for DRC MCM XT Condition Monitoring System.

Technische informatie DRC LC M3

Surge arrester for use in hazardous areas

Pluggable multi-pole universal surge arrester for use in intrinsically safe systems. The SPD modules with integrated LifeCheck element allow for quick testing by means of the portable DRC LC reader or stationary DRC CMC condition monitoring device in non-explosive atmospheres. SPD module and base part have to be ordered separately.

• Effective protection with minimum space requirements (only 3.0 mm per pole)
  
• For use in 2-pole, 3-pole or 4-pole intrinsically safe interfaces
  
• Function-optimised design for easy installation and safe handling
  
• Allows for quick testing of SPD modules with LifeCheck
  
• Certified by ATEX and FISCO
  

Technische informatie BLITZDUCTOR^® XT Ex (i)

TW DRC MCM EX

• Arrangement of non-intrinsically safe and Ex i circuits directly next to each other (gaining of space)
  
• Increase of the thread measure to ≥50 mm in accordance with EN 60079-11
  
• Suitable for mounting rails with a height of 7.5 mm and 15 mm
  
• Easy installation by means of snapping the partition onto the mounting rail

Certain installation conditions have to be adhered to when using BLITZDUCTOR XT Ex (i) arresters in intrinsically safe circuits.
In accordance with EN 60079-11:2007 (VDE 0170-7) a minimum distance (thread measure) of ≥50 mm has to be maintained
between intrinsically safe and non-intrinsically safe circuits!
When using the Ex i separation type TW DRC MCM EX, this distance is also maintained if the devices are arranged directly next to each other.